| IEC 62271-200 scope | Metal-enclosed AC switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV. | Confirm that the proposed assembly falls within this voltage range and is intended for the required indoor or outdoor installation. | Check the declared standard edition, rated voltage, installation conditions, and manufacturer’s type-test documentation. |
| Rated voltage and insulation level | Rated voltage, power-frequency withstand voltage, and lightning-impulse withstand voltage. | Choose ratings suitable for the system voltage, grounding arrangement, and specified insulation coordination. Common market voltage classes include 12 kV, 24 kV, and 36 kV; availability and system conventions vary. | Compare nameplate ratings and insulation levels with the project’s electrical design and applicable local requirements. |
| Frequency | System frequency and equipment frequency rating. | IEC 62271-200 covers AC equipment at frequencies up to and including 60 Hz. Specify the actual network frequency, commonly 50 Hz or 60 Hz. | Confirm the switchgear and associated protection equipment are rated for the project frequency. |
| Transformer protection arrangement | Transformer rating, primary-side protection concept, expected inrush current, and downstream protection coordination. | Depending on the design, transformer feeders may use a circuit breaker with protective relays or a switch-fuse combination. The correct arrangement depends on transformer and system data; neither is universally suitable. | Review protection studies, transformer data, fuse or relay settings, and coordination with upstream and downstream devices. |
| Continuous current | Rated current of the busbar, feeder, and switching devices. | Size for the maximum expected continuous load, ambient conditions, enclosure arrangement, and any specified future capacity. Check each component’s rating, not only the switchgear lineup rating. | Verify current ratings against load calculations and the applicable temperature-rise test conditions. |
| Short-circuit withstand and interruption | Rated short-time withstand current, duration, peak withstand current, and circuit-breaker breaking capacity where applicable. | Base ratings on the calculated fault level at the installation point. Ensure the assembly and each relevant switching device can withstand or interrupt the required fault duty. | Compare the project short-circuit study with declared ratings and review the relevant test reports. |
| Internal arc classification (IAC) | Whether an internal arc classification is required, along with accessibility type, accessible sides, and rated arc duration. | Specify IAC according to personnel access and the installation’s safety strategy. IAC is a classified performance under stated test conditions, not a guarantee against every possible event. | Check the complete designation and test configuration, including accessible sides and installation clearances. |
| Loss of service continuity (LSC) | Required ability to keep parts of the switchgear operating while a compartment is accessed or isolated. | Select the LSC category to match operational continuity needs and the consequences of taking a feeder or compartment out of service. | Confirm the declared category and understand which compartments or circuits can remain energized during maintenance. |
| Partition class | Partitioning between compartments and whether partitions are metallic or insulating. | Review the declared PM or PI class and the intended separation of busbar, switching-device, cable, and low-voltage compartments. | Check the design description, access procedure, and test documentation for the specified partition class. |
| Enclosure and environment | Indoor or outdoor installation, ambient temperature, altitude, humidity, pollution, corrosion, and ingress protection. | Specify site conditions and the required enclosure protection. Ingress-protection classifications are addressed by IEC 60529; confirm any necessary correction or special design for site conditions. | Review the declared IP rating, environmental limits, altitude assumptions, and any derating or mitigation measures. |
| Earthing and interlocking | Earthing-switch duty, cable-side earthing needs, and mechanical or electrical interlocks. | Match the earthing arrangement to the network and operating procedures. Interlocks should prevent unsafe operating sequences identified by the project design. | Review circuit diagrams, interlocking logic, operating instructions, and earthing-switch ratings. |
| Transformer and cable interface | Cable type, termination arrangement, conductor size, transformer connection, and available installation space. | Confirm that the cable compartment and termination design suit the specified cables and site layout. Check clearances, access, and cable bending requirements. | Approve interface drawings and verify compatibility with the transformer, cable system, and civil works. |
| Documentation and compliance | Type-test evidence, routine-test records, ratings, drawings, instructions, and applicable national or project rules. | IEC 62271-200 defines relevant requirements for the covered metal-enclosed assemblies; it does not determine every project rating or replace local regulatory requirements. | Request a compliance schedule, test evidence for the offered configuration, and complete project-specific technical documentation. |